math and applied math : drawer : coal analyze : metallurgy : highway : highway Project programme : pharmacology > ductility
Contents
No. 1
  Plasticity is a load in a given material under permanent deformation of material properties, for most engineering materials, when the stress below the proportional limit, the stress-strain relationship is linear. In addition, most of the material in the stress below the yield point, the performance of elastic behavior, ie, when the removal of load, the strain has completely disappeared. Plastic elongation δ and the quality of available cross-section shrinkage ψ said.
  As the difference between the yield point and the proportional limit is very small, so in the ANSYS program, assuming they are the same. In the stress-strain curve, below the yield point is called elastic part, over the plastic part is called the yield point, also known as strain hardening part. Considered in the analysis of the plasticity of the material properties of the plastic zone.
  Path dependency:
  Since plastic is not restored, then the problem with the loading history on the type of nonlinear problem called path-related or non-conservative and non-linear.
  Path dependency refers to a given boundary conditions, there may be multiple correct solutions - internal stress and strain distribution - there are, in order to be truly accurate results, we must follow the system through the loading process to load the real .
  Rate correlation:
  The size of the plastic strain may be a function of speed of loading, if the size of plastic strain with time, this plastic is called rate-independent plasticity, on the contrary, the strain rate is called the rate of sexual-related plasticity.
  Most of the material has some degree of rate-dependent, but in most of the static analysis of the strain rate experienced by the scope of both the stress - strain curve is not very different, so in general analysis, we become a and rate-independent.
  Engineering stress, strain and true stress and strain:
  Plastic material data generally tensile stress - strain curve given in the form. Material data may be engineering stress (p/A0) and engineering strain (dl/l0), may also be true stress (P / A) and true strain (Ln (l/l0)).
  Large strain plasticity analysis of commonly used real stress, strain and small strain analysis of the data commonly used engineering stress and strain data.
  When activated plastic:
  When the stress exceeds the material yield point, plastic is activated (that is, there is plastic strain occurs). The yield stress itself may be one of the following parameters.
  • Temperature
  * Strain rate
  * History of previous strain
  * Confining pressure
  • Other parameters
  In physics, the plastic that is normative, and relatively flexible.
  Reinforced plastic indicators: cold performance, elongation
Translated by Google
Encyclopedia
  Plastic
  plast main eitv
  Plasticity of plastic materials under external force of permanent irreversible
  For a long time without destroying the ability of deformation. Also known as normative. It said the material in the static
  Load to yield or rheological performance.
  Metal plastic, usually made with smooth tensile test specimens to be
  The total elongation and area reduction rate will be represented by two indicators
  . Award Guide to persuade each other 00 accounts,. A double-cross each other to adopt 00%
  10 a corpse 0 -
  Type in the island, 11 were pulled off the gauge length before and after; F0, who were
  The original specimen cross-sectional area and fracture (necking) at the cross-sectional area. By plastic
  Size, material can be divided into: plastic material is greater than 2 to 5% valley), such as
  Copper, steel, etc.; brittle material cushions less than or equal to 2 to 5%), such as cast iron
  And so on. Plastic materials and also the way the force. Biaxial or triaxial extension
  Plastic deformation before fracture by one-way stress is much smaller than, typically plastic
  Metal under stress in this is also shown as brittle. In recent years, has found a
  These materials with superplastic, the total strain of more than 1000%.
  The crystalline material to produce plastic deformation mechanisms include: ① dislocation slip
  Shift; ② twin; ③ kink. Which dislocation slip is plastic deformation basic
  Form. Plastic deformation of amorphous materials is due to external forces to make atomic, sub-
  Child from the equilibrium position occurs viscous rheology.
  Plastic deformation process is complex, between the stress and strain there is no simple
  Single mathematical relationship between the mathematical theory of elasticity is much less mature. Plastic
  Metal is mainly used in the study of the theory of creep, plastic flow and pressure processing,
  Predict the ultimate strength and yield component characteristics.
  (Zong all)
    
Translated by Google
English Expression
  1. :  plastic layer index
  2. n.:  ductility,  flexibility,  plasticity
Thesaurus
fanxing
Related Phrases
buckleWikipedia Daquanelementrhenium
phoenix effectcrystal temperaturejigfashioning
forge and pressclosenesschemisecommodity
Containing Phrases
deformabilitythermoplasticity